ACD110-12 | GAC 12VDC / Deutsch Connector without Mating Connector / Same as ACD110A

Multi-VDC / Light-Force (Low-Current Optimized PID) / For Cummins EFC Forward Acting (Normally Closed)

24VDC / Male Push-On Terminals / Isuzu L-Series 3LB1, 3LD1, 3LD2, 4LE1, 4LE2

5 in. [127mm] Thread Length / 12in. [305mm] Harness / Flying Leads / Stainless

12VDC / Light-Force (Low-Current Optimized PID)

12VDC / Packard Connector without Mating Connector / Perkins 404D-15, 404D-22 & Caterpillar C2.2T, C3.4

24VDC / Standard Unit with Idle

MSP Automotive Sensors - 10 ft. [3m] Shielded Cable / 2-Terminal

Multi-VDC / Cummins QST30 & QSK45-78 to GAC LSM/SYC

Multi-VDC / Two Oxygen Sensor Inputs (Pre and Post Catalyst) and EGT (Type-K Thermocouple) Input

3.19 in. [81mm] Thread Length / 6.25 in. [159mm] Harness / Packard Connector / Same as MSP6728 with Mating Connector Kit EC1350 / Stainless

10 Turn / 1KΩ

24VDC / Barber Colman - Dyna 1 & 8000 Speed Control to GAC LSM/SYC / 5kΩ Trim Pot Input / Selectable 50/60Hz Operation

2.7 in. [69mm] Thread Length / 1 ft. [0.3m] Shielded Cable / Flying Leads / Stainless

AFR Series - 8 ft. [2.4m] Harness / Flying Leads / 35-Wires

1/4 in. I.D. End and 1/4-28 UNF-2B Thread 0.719 in. Deep

175 Series Installation Kit - Bosch A Pump / Right Hand Rack - Includes Adapter Plate, Bearing Retainer (KT176A), Spring, Gaskets, Linkage, Hardware

24VDC / Standard Unit

24VDC / Packard Connector with Mating Connector Kit EC1300 / With Installation Kit KT292 (O-Ring, Bolts)

USB to RS232 Adapter for PC Interface, GAC Recommended

ACE275K, ACE295F, ATBT2/T3-F, 175/176AF (AB Position Sensor) Actuators - Mating Connector Kit / 6-Terminal

EDG6000 Series - Mating Connector Kit / 14-Terminal

3.86 in. [98mm] Thread Length / 1 ft. [0.3m] Harness / Flying Leads / Aluminum Clear Anodized

12VDC / Standard Unit

3.19 in. [81mm] Thread Length / 6.25 in. [159mm] Harness / Packard Connector without Mating Connector / Stainless

Multi-VDC / Replacement for Most ESD5500E Series in a Single Unit

Installation Bracket - ALN025 Starter Plate (Rectangular with Holes Pre-Drilled for Mounting Actuator)

Multi-VDC / Anti-Windup Circuit (Gaseous) / Recommended for T3/T4 ATBs

24VDC / Packard Connector without Mating Connector / Includes KT295 Installation Kit

24VDC / Barber Colman Dyna 2 Load Sharing (80100, 80101, 80104, 80105) to GAC ESD

12VDC / Packard Connector without Mating Connector / Single (ADD) or Double Rack Bearing (ACD) / Bosch Install Kit KT289 (ADD) or BYC ASIMCO KT283 (ACD) Included

24VDC / Universal / 1-4VDC Input / 4-20mA Output / Deutz Position Interface

24VDC / Packard Connector without Mating Connector / Lever Included

1 Turn / 20KΩ / With Knob / Droop Control

Multi-VDC / Standard Unit

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m]

10VDC (From Speed Control) / Basic Isochronous Load Sharing / Load Anticipation / Droop