MSP676 | GAC 5 in. 127mm Thread Length / 12in. 305mm Harness / Flying Leads / Stainless

Multi-VDC / Built-In Display / Terminal Strip / All Actuators (Including ACB2001) / Built-In Configurable Speed Switch Output / Advanced CAN J1939 support / Battery Voltage, Hour Meters / Variable Speed 0-5VDC or 4-20mA Input

MSP Packard Sensors - Connector Kit Replacement / 2-Terminal

24VDC / Packard Connector without Mating Connector / Install Kit KT291 Included

MSP Automotive Sensors - 10 ft. [3m] Shielded Cable / 2-Terminal

24VDC / Right Side Stop Assembly / Installation Kit (Gasket, Bolts) Included

5-Star Torx Bit - Pump Cover Screws (Service Tool)

Multi-VDC / Automatic Synchronizer with Sync Check Relay

Non-CE / 24VDC / Isochronous Load Sharing / Load Anticipation / Droop / Forward and Reverse Power Monitoring and Reset Capability

ADC Commercial Actuators - 4 ft. [1.2m] Harness / 2-Terminal

12VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / Greater Rate Return Spring SP207

12VDC / Standard Unit

12VDC / Light-Force (Low-Current Optimized PID)

EDG6000 Series - 8 ft. [2.4m] Harness / Flying Leads / 14-Wires

CE-Compliant / 24VDC / Isochronous Load Sharing / Load Anticipation / Droop / Forward and Reverse Power Monitoring and Reset Capability

3.19 in. [81mm] Thread Length / 7 in. [178mm] Harness / Flying Leads / Stainless

24VDC / Cummins EFC Speed Control to GAC LSM/SYC / 5kΩ Trim Pot Input

24VDC / Woodward Load Sharing & Synchronizing (0+/-3V DC Output) to GAC ESD / Including DEC2

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / Lesser Rate Return Spring SP203 / Thin Rubber Stop 26 Degrees Travel

SDG Series - Deutsch Mating Connector Kit / SDG514 & 524 / 12-Terminal

MSP Military-Style (Amphenol) Sensors - 10 ft. [3m] Shielded Harness / Straight Connector EC1100 / 2-Terminal

24VDC / Military-Style Connector without Mating Connector / Position Feedback Sensor (Novotechnik) / Note - Compatible with EEG6500 Series

12VDC / Light-Force (Low-Current Optimized PID)

M5 I.D. End and Thread 14mm Deep

5.0 in. [127mm] Thread Length / #8-32NC-2A Thread Stud Terminals / High Output 1.3kΩ

Basic Engine Controller / Crank Pause and Overspeed Switch / Preheat Capabilities / Keyswitch

24VDC / Packard Connector without Mating Connector / Yanmar TNE and TNV Series 2TNE, 3TNE, 4TNE and 2TNV, 3TNV, 4TNV & Isuzu C-Series 2CA, 3CA, 3CB, 3CD, 3CE

Multi-VDC / Perkins 1306-E87 7M351 to GAC LSM/SYC

12VDC / Packard Connector without Mating Connector / Includes GA102

ADD (Packard) Actuators - Connector Kit Replacement / 2-Terminal

3.19 in. [81mm] Thread Length / 2.75 in. [70mm] Harness / Automotive Connector / Stainless

24VDC / 6.5 lbf. [3.0 kg] / 0.25 ft-lb [0.34 J] Work / Male Push-On Terminals

3.0 in. [76mm] Thread Length / Military-Style Connector / Same as MSP6714 except with Mating Connector Kit EC1100 (Straight) / Stainless

Multi-VDC / SMARTTOUCH® Keypad / Fixed & Variable Speed / Droop

24VDC / Barber Colman - Dyna 1 & 8000 Speed Control to GAC LSM/SYC / 5kΩ Trim Pot Input / Selectable 50/60Hz Operation

Installation Bracket - ALN050 Starter Plate (Rectangular with Holes Pre-Drilled for Mounting Actuator)

175 Series Installation Kit - Bosch EDC Governor Housing - Mounting Plate, Linkage, Gasket, Hardware